Safety Inspectors UK Ltd

ADVICE & INSIGHTS

Changing tools does not reset a grounds worker’s vibration exposure

Illustrative grounds worker reviewing a schedule beside a utility vehicle and tools; headline: Different tools. One daily exposure.
GROUNDS MAINTENANCE · PRACTICAL GUIDE

Planning hand-arm vibration exposure across a working day · 5 minute read

The hedge is finished. The brushcutter comes out. The worker’s vibration exposure has not started again from zero.

A grounds team can move between several tools, sites and supervisors in one shift. If each job is checked separately, the combined exposure can disappear between the paperwork. The management question is simple: who can see the whole day for each person?

For North East grounds contractors and estate managers, this is a useful check before allocating work. The legal framework described here applies across Great Britain; it is not a new local rule or a newly announced change.

Build the assessment around the person

List the vibrating tools each worker may use, including occasional help for another crew. Record the tool model, task, vibration magnitude used in the assessment and time actually exposed. Travel, loading and breaks are not automatically tool operating time.

HSE’s risk-assessment guidance explains how to establish exposure from vibration magnitude and duration. Observe representative work rather than relying on a rough estimate of how long the job takes. Check that supplier data reflect the tool’s real use; published figures may underestimate exposure.

A practical worksheet can have one row per tool and task, but it needs a daily total for the worker. Give a named supervisor responsibility for changes. An extra half-hour helping another team must reach that person before the work is allocated, not only when timesheets arrive.

Know what the action and limit values mean

Under the Control of Vibration at Work Regulations 2005, the daily hand-arm vibration exposure action value is 2.5 m/s² A(8); the exposure limit value is 5 m/s² A(8). A(8) expresses daily exposure normalised to an eight-hour reference period. It does not mean eight hours of tool use is permitted.

HSE sets out employers’ responsibilities: assess and control risks, provide information and training, and arrange health surveillance where required. Reaching the action value requires a planned programme of controls. The limit must not be exceeded; neither value is a target to use up.

HSE’s calculator guidance converts exposure into points: 100 corresponds to the action value and 400 to the limit. Purely as an illustration, 60 points from one task plus 50 from another gives 110 for the day. These are invented calculation inputs, not ratings or time allowances for particular tools. Use representative data for your equipment.

Does the written assessment match the working day?

An inspection can help identify gaps between procedures, supervision and everyday practice. Start with the tasks your team actually carries out.

Explore health and safety inspections →

Reduce exposure before adding another timer

Look first for a different method that removes or reduces hand-held vibrating work. Choose suitable, efficient equipment with lower vibration, and maintain it properly. A tool that struggles with the task can leave the operator exposed for longer.

HSE’s control guidance also covers limiting exposure time and organising work to avoid long continuous periods. Rotating someone between two vibrating tools still contributes to their total. Include genuinely non-vibrating duties where appropriate. Gloves may help keep hands warm, but should not be relied on as vibration protection.

If you use electronic monitoring, decide who responds before the planned exposure is exceeded. HSE warns that retrospective recording can identify an exceedance too late. Monitoring alone does not control the risk. Where suitable vibration data cannot be obtained elsewhere, arrange competent measurement rather than guessing.

Five checks before the team leaves

  • Whole-day view: combine every planned vibrating task for each worker, including work at another site.
  • Credible inputs: identify the tool and task, representative vibration data and actual exposure duration.
  • Controls agreed: confirm suitable equipment, maintenance and a work plan that reduces exposure.
  • Changes controlled: name the supervisor who must approve extra tasks or replacement tools and reassess the total.
  • Health concerns heard: explain how workers report symptoms promptly and ensure required health surveillance is arranged.

Ask workers whether the plan reflects a normal busy day. Keep occupational health advice confidential and act on fitness or exposure restrictions. Health surveillance helps detect problems; it does not replace prevention.

Make the next grounds shift easier to supervise

Bring your tool list, current assessment and a typical work schedule. Safety Inspectors UK can discuss your management arrangements and practical next steps. For ongoing support, explore our retained safety services.

Request support

Sources checked: 17 November 2026. The linked HSE pages provide the national guidance and explanation of legal duties used above. The checklist is a practical management aid, not a substitute for your task-specific assessment.

Cover: AI-generated illustrative grounds-maintenance scene; not a real customer, worker or incident.

Call usEmail us WhatsApp us